13 ms·

Build a do-it-yourself home air purifier for about $25

• smmnyc 8y ago
  Is there an advantage to attaching the filter to the front of the fan so air is blown through it (as shown in the video) versus taping it to the back of the fan so air is sucked through it? Just curious if that would make any difference. It might be easier to get the filter to stay if it's getting sucked to the fan.
  • dtromero 8y ago
    Not sure, but I'd think it would also help to keep your fan clean.
    • 9wzYQbTYsAIc 8y ago
      I’ve actually built this fan “mod” and when I change out the filter, I’m going to try attaching it to the back instead. With the filter thoroughly taped to the front (nearly airtight), there’s a large amount of blowback. I suspect that this is reducing the overall efficiency of air filtration.
      • jhenkens 8y ago
        With it taped to the back, you don't get blowback, but there is significantly reduced airflow out the front. I used a filter of this type for ~2 weeks during the Thomas fire. Worked very well, though the proper filter I received from Amazon a week after I built this worked better. Two is better than one, though!
  • io_io 8y ago
    I would guess that it works similar to a water pump- pushing is always more powerful than sucking - but check this out for some detailed analysis (and more data on DIY air filters) https://smartairfilters.com/en/blog/where-should-an-air-filter-be-placed-relative-to-the-fan-for-best-efficiency/ https://smartairfilters.com/en/blog/where-should-an-air-filt...
    • patrioticaction 8y ago
      I never would've guessed turbulent air would be more difficult to push but it makes total sense! Great find.
    • ex_amazon_sde 8y ago
      Excellent page.
  • patcheudor 8y ago
    Placed in front it would catch particles coming off the motor like lubricant, bits of metal from bearings and carbon particles from the brushes if it's not a brushless motor.
  • cwkoss 8y ago
    I think the answer is yes, but I'd also like to to know why.
  • adventured 8y ago
    Perhaps strain on the cheap box fan motor as it tries to pull its air through the filter. I've gone through a number of those style of cheap box fans over the years, any kind of long-term resistance very near the intake seems to cause the equally cheap motors harm and shorten their functioning life considerably. I haven't seen the same motor damage problem with resistance added to the exhaust side. In absence of that experience I would have guessed that similar resistance on either side would harm the junk motors all the same.
    • joezydeco 8y ago
      I'd agree with this. I used to put the high-efficiency filters on my furnace, my HVAC guy said these filters are so heavy that they put a strain on the blower motor. It's better for the motor to use a plain blue fiberglass filter (MSRP $1). You're not really filtering that much out of a closed house, unless you run your forced-air A/C or Heat with the windows open.
      • johnbrodie 8y ago
        We upgraded to a "media filter" when we got new HVAC at my house. IIRC they are 4 inches thick, which gives a lot more surface area due to the deep pleats. You can then run fairly tight filters without putting undue strain on the motor - plus they last quite a bit longer. It made a moderate difference in our house in regards to dust in the air, but we also have 3 pets and live in a very dry, dusty area.
      • adventured 8y ago
        I did the same thing with my furnace. Just to try it I switched to a high merv filter rating and could immediately notice the considerable reduction in air flow that it was causing (and presumably increased strain on the furnace). Seeing as it was a bit more restrictive than I expected, I ended up ditching that and going back to a weaker merv rating filter (haven't gone back to the blue fiberglass style filters, just going with a weaker merv seems to do the trick, haven't had any problems with increased wear on the furnace in the last ~8 years).
      • olivierlacan 8y ago
  • deleted 8y ago
    [deleted]
  • yumraj 8y ago
    I can think/guess two reasons: 1) If the filter is at the back, since the air is pulled through it, the dirty side is outside where people and kids can touch it as it builds up. If the filter is in the front, the dirty side is inside (towards the fan blade) while the clean side is outside. 2) If the filter is at the back, due to air's resistance it is possible, due to nooks/gaps in the fan, that the some of the air may be pulled from elsewhere and not all the air may pass through the filter. If the filter is in the front, it is easier to seal between the fan and the filter to make sure all air is pushed through it.
    • asah 8y ago
      always wondered this myself... #1 - good point! I'm curious... doesn't #2 cut both ways? i.e. if you can seal the front, you can seal the back?
  • nhebb 8y ago
    I can confirm what others said about air drag. I've done this in the past, assuming I needed the filter on the input side. I had to use two filters, some cardboard, and plenty of duct tape to create a triangular input in order to get a decent amount of airflow. I wish the guy on the video would take an air reading measurement near the side of the filter. I'm guessing that a lot of unfiltered air is escaping out the sides.
  • sjg007 8y ago
    probably makes the fan quieter.
  • giardini 8y ago
    FWIW if you tape the filter to the back then the fan doesn't get dirty as quickly. [Every now and then you should clean the accumulated dust off a fan.] BTW you need not cover the entire area of the fan with filter material. So, for instance, if your fan's breaker is shutting the motor down b/c of the load of the filter, you can slide the filter up to cover less of the fan with the filter, reducing the load on the fan motor. While not all air passing through the fan will be filtered, over time most air will eventually pass through the filter and the room will be cleared of particulates. Similarly, it is not necessary that the filter be the same shape or size as the fan, since with each pass at least part of the airstream is cleaned. Eventually all the air in a room will pass through the filter area.
• baby 8y ago
  I've been luring the Dyson hot and cool air purifiers, it's pretty silent from what I've heard, it also serves as both an electrical heater during the winter and a cooler during the summer. The price tag is the reason I've never bought one...
  • glibgil 8y ago
    > cooler during the summer Where does the heat go?
    • tjohns 8y ago
      It's just a fan + heater. It's not an air conditioner, nor is it marketed as such. I have one. It works pretty well. The air filter isn't as good as the massive Austin Air I use for my living room, but it's okay for a smaller room... not to mention much quieter, smaller, and easier to integrate with home automation.
    • alphabettsy 8y ago
      Just like any fan, it makes you feel cooler. It doesn’t actually cool the air.
    • deleted 8y ago
      [deleted]
  • leetbulb 8y ago
    Screw Dyson. Get a Winix HR1000. You can find them cheap ($200 or so) on eBay every so often. I picked up two a couple years ago and am very happy with them. You only need to replace the filters once a year. They've made a HUGE difference with my allergies. They automatically adjust airflow based on built-in air quality sensors. They are completely silent, aside from the "turbo" mode (~300CFM lol), but if you like white noise, it's great.
    • mattlondon 8y ago
      We recently got a Winix U300 (1) for about £150 new. It is basically a HEPA + Activated Charcoal filter and it claims it has some "plasmawave" thing that generates "free radicals" that kills odors and viruses. Initial searching suggests that this might be true, but I am unsure if there is any way to really test it. The air quality sensor certainloy works if you drink a strong coffee then go and blow into the sensor - the fans crank up the speed hugely to compensate for the stinking coffee breath! :) Only criticism is that the U300 does not have wifi connection - only IR control... I am hacking up a esp8266 + some IR LEDs and photoresistors to monitor and control it via MQTT though which is fun. The "wifi connected" units seem to add several hundred GBP to the price for the same filtering performance. We're not sure if we're noticing any actual improvements in air quality, or just imagining it...! :-) The placebo effect is quite good if nothing else. Noses feel less congested, and the air in the room feels less stuffy in the morning. 1 - https://winixeurope.eu/air_purifiers/winix-u300/ https://winixeurope.eu/air_purifiers/winix-u300/ No personal connection to these guys, just a satisfied customer (so far after a few months)
• adamwong246 8y ago
  I do this and it works wonders if you have pets. Tips: - run this homemade air purifier when you are vacuuming, as that tends to agitate particulates a lot - get 2 filters, a cheap low grade and a premium, high-HEPA-rated filter. Stack them together and you can replace the cheap one frequently and the expensive one less frequently.
  • iscrewyou 8y ago
    I know what I am doing this coming weekend!! I am so tired of dust in my studio. There is no ventilation other than the small fan in the bathroom or the big sliding door in the front. So I leave the fan turned on overnight but because of pressure difference, very small particles keep accumulating all over my place. I’m really hoping this changes that.
  • culot 8y ago
    Swedish tracing paper works well for a pre-filter. It's inexpensive for a long, seemingly inexhaustible roll, and can be washed numerous times. It also works well by itself if you just want to cheaply filter large particulates. I used to use it in those cheap $40 Hamilton Beach air purifiers. The OEM filters for those cost almost at much as the new unit and wear out [for me] within a couple of weeks. That setup with Swedish tracing paper works well for dust, as a supplement for my HEPA filter purifier.
  • zacharycohn 8y ago
    Does it go: Fan --> Cheap Filter --> Expensive Filter Fan --> Expensive Filter --> Cheap Filter Cheap Filter --> Expensive Filter --> Fan Expensive Filter --> Cheap Filter --> Fan ?
    • linschn 8y ago
      Cheap Filter --> Expensive Filter --> Fan You put the filters on the intake, so that the airflow helps making a seal instead of creating leaks. You put the cheap filter first everything that it catches will not clog the expansive one.
• fenwick67 8y ago
  At first glance this looks ridiculous until you realize it's a doctor from U of M's health center demonstrating its effectiveness
• 51lver 8y ago
  I used a very thick (4") filter rated for smoke particles when the wildfires this year blew their smoke down to Seattle. The filter went from white to a very interesting shade of grey in 3 days. Wife was able to sleep again though, so it does work very well in my experience. (20x20 fan, filter on intake side)
  • Kadin 8y ago
    Out of curiosity, where were you able to find the big 4" thick filters in the 20x20 size? I wasn't able to find anything other than the usual 0.75 thick furnace dust filters in 20x20 for a box fan.
    • lubujackson 8y ago
      I just bought a 4 pack from Amazon Prime Now in SF, YMMV.
    • 51lver 8y ago
      Ace hardware. It was not cheap.
• peepopeep 8y ago
  I was looking up air quality monitors but can't seem to find any on amazon with a calibration certificate that will accurately measure 0.3 micro particles. Am I the only one who thinks this is a great opportunity for a smart product with an app that has the features of a professional air quality monitor and simple UI / UX? If such product exists, does anyone know where I can find it?
  • io_io 8y ago
    With the recent California fires, I've been looking for a decent option. Unfortunately the Elgato Eve sensor is no longer sold, and the few other consumer products still hover in the $100+ range with poor reviews. PurpleAir sells an indoor sensor, but it appears to be limited release and somewhat 3D printed. https://www.purpleair.com/ https://www.purpleair.com/
    • mmagin 8y ago
      Having both, I'd say that the indoor sensor is not worth it. It doesn't have both sensors so it isn't equipped to test them against each other. I do like the outdoor sensor though.
      • peepopeep 8y ago
        What are you using for indoors?
    • pat2man 8y ago
      The new version of the Eve Room sensor seems to be out: https://www.amazon.com/Elgato-10EAM9901-Generation-Technology-Temperature/dp/B07GKVBYKV https://www.amazon.com/Elgato-10EAM9901-Generation-Technolog...
      • lprd 8y ago
        How does Eve Room compare to the Netatmo Home Coach?
  • 8y ago
• walrus01 8y ago
  Over the past two years as BC and WA have had terrible forest fires, this exact solution has become quite popular for people who are willing to DIY. the air quality in mid summer 2018 in Vancouver was really quite bad, exceeding Delhi or Beijing pm2.5 figures for weeks.
  • selimthegrim 8y ago
    Was Seattle as bad PM2.5 wise?
    • walrus01 8y ago
      Yes... https://www.vox.com/energy-and-environment/2018/8/21/17761908/seattle-air-quality-haze-smoke-wildfire-health https://www.vox.com/energy-and-environment/2018/8/21/1776190...
• Dowwie 8y ago
  To what extent will a box fan like that successfully circulate most of the air in a room through the filter?
• cheunste 8y ago
  I been pondering about this solution for months since my air purifier died back early summer. I also have an additional idea to make it more automatic by using a raspberry pi, hooking it up to a powerswitch tail (essentially cutting power to a fan) and have it automatically turn on and off depending on time of day, etc.
  • deleted 8y ago
    [deleted]
  • wbrasky 8y ago
    instead of a raspberry pi and all that entails, might I suggest a simple outlet timer
    • core-questions 8y ago
      Good time of year to buy them, too, what with the christmas lights and all that. $5 ballpark.
      • jjeaff 8y ago
        I have seen the mechanical style ones at the dollar store. I wouldn't set my watch by it, but would be fine for this purpose.
  • io_io 8y ago
    I have mine on a homekit enabled outlet ($20) for scheduling and presence-based triggers. Unfortunately I haven't found a homekit enabled air quality sensor to pair with it.
    • pat2man 8y ago
      Eve room? https://www.evehome.com/en/eve-room https://www.evehome.com/en/eve-room
      • io_io 8y ago
• pwarner 8y ago
  I've been running a 3M Filtrete MPR 2800 in my furnace filter. https://www.purpleair.com/ https://www.purpleair.com/ confirms it works. There house averages maybe 60 PM 2.5 vs 200 outside. Don't know how good it is for furnace, but it hardly runs otherwise in Northern CA.
  • mikenew 8y ago
    Do you have two air sensors, or do you just have one indoors and compare it with weather data?
    • pwarner 8y ago
      I am relying on 2 purple air sensors 10 miles away in opposite directions for an outside estimate. They are usually within 10%, and we are in the same valley, so should be close. I also see when I stop the furnace fan, levels spike. Then drops when I turn on again...
  • deleted 8y ago
    [deleted]
• yonran 8y ago
  Is there anywhere you can get a good blower fan for the purpose of filtering the air, instead of a box fan that has a lot of space around the blades?
  • vt240 8y ago
    Grainger [1] search for "industrial Blowers and Accessories" would probably be a good place to start looking. They tend to be expensive though. Take a look at McMaster-Carr [2] too. [1]: https://www.grainger.com https://www.grainger.com [2]: https://www.mcmaster.com/ https://www.mcmaster.com/
• leon_sbt 8y ago
  Generally there are two classes of objects that you want to filter for. Particulates and VOC (Volatile Organic Compounds). Think of particulates as specs of dust with varying size and VOC's as random chemical compounds such as spray paint, smoke, oders. The general go-to clean room/industrial filter stack is Prefilter(F5 Bag)->HEPA->Activated Carbon. The pre-filter catches all the big particulates to prevents clogging the HEPA filter. The HEPA filter catches all of the really small particulates. The activated carbon captures most of the VOC's/oder/smoke. The official way to monitor when a particulate filter is bad, is to measure the pressure drop across the filter, and compare to manufacture specs. For the carbon filters, you would install a gas sensor measuring whatever chemical your trying to scrub. When there is a spike in that particular gas compound from your sensor. You know the carbon filter is saturated, and should be changed. It looks like the the filter mentioned in the article video,combines all the filter products into a single product. Nice! If your air handler can manage the increased pressure drops, please buy the most legit filters you can buy. It's literally the cheapest insurance you can buy.
  • clairity 8y ago
    > “The general go-to clean room/industrial filter stack is Prefilter(F5 Bag)->HEPA->Activated Carbon.” yup, i bought a blueair 211+ (https://www.blueair.com/us/blue/blue-pure-211/1695.html https://www.blueair.com/us/blue/blue-pure-211/1695.html), that has exactly those filter elements in a nice (if bigger than expected) package. this model was recommended by both consumer reports and the wirecutter (until recently, cynically thinking they didn’t pay wirecutter’s “endorsement fees”). it’s effectively eliminated my constant coughing, sneezing and runny noses before i got it.
    • eli 8y ago
      Wirecutter doesn’t have endorsement fees
      • gruez 8y ago
        they don't, although if they recommend you, they'll ask you for a cut of sales (affiliate program). if you say no, they'll switch their recommendation to your competitor and never review your brand again. https://news.ycombinator.com/item?id=16729408 https://news.ycombinator.com/item?id=16729408
• soneca 8y ago
  When and for how long should I leave this turned on to be effective in removing dust particles in my small bedroom?
  • ghayes 8y ago
    For my air purifier, it generally reports better air quality in less than ten minutes of running at full speed. But, if you're in an area affected by the wildfires, then new particles will also be entering your home / bedroom, so you may want to keep it on low or run it in cycles.
  • adventured 8y ago
    Are you ok with white noise while you're sleeping and air flowing in the room? If you're ok with those things, run it while you're at home and sleeping. If you go to work during the day turn it off then, and turn it back on when you get home. It should rapidly clean up the air in a small bedroom. The only real issue is any continual air flow into the room. There will be a big impact from what kind of air system you have in the greater building. For example, central air without a good filter on that system will make your fan-filter's job a lot harder. The filters are relatively cheap to replace and will last a long time filtering a small bedroom. I get a solid year out of the filter on my central air system and it's filtering an entire home (non-smoking, no pets). Outside of the small electrical cost or annoyance from having the fan running, there's no reason not to run it very frequently if you derive a benefit. If you don't desperately need purified air for eg allergy purposes and your small bedroom isn't receiving inbound air (eg from a central air system), run it for 20-30 minutes, a few times per day, and that should easily do the job. If that's a hassle, just let it run more often than not.
• ed_balls 8y ago
  I wonder if you'd put cotton wool, how effective it would be. Here is my set up: - I bought XIAOMI Mi Air Purifier 2 straight from China for $137.00 and spent 1 euro on a EU plug. It's so quiet that I can sleep next to it, looks nice and it's quite compact, so doesn't take up much space. It has a particle detector to adjust the fan speed. The app is useless, so a cheaper version without WiFi and bluetooth would be great. - Buy some HEPA filters to put into window ventilation. You may want to remove some plastic inside to increase the flow http://img.archiexpo.com/images_ae/photo-g/69621-5895915.jpg http://img.archiexpo.com/images_ae/photo-g/69621-5895915.jpg - Buy roomba like vacuum cleaner https://www.goodcheapandfast.com/articles/best-robot-vacuums https://www.goodcheapandfast.com/articles/best-robot-vacuums It will cost you less than 500$ to buy these and about 55$/year for new filters. It is worth the money. The air quality is much better (I'm allergic and I haven't had any problem with my sinus since). What is more, is it worth it. It will save you time cleaning your place (about 10h/year) Anyone has tried robot vacuums with mop or automatic dirt disposal function?
  • blattimwind 8y ago
    > I wonder if you'd put cotton wool, how effective it would be. Not very. Wet wool is better, but only as long as its wet and clean. > XIAOMI Mi Air Purifier 2 straight from China Interesting question. Does the removal of particulates offset the health impact of its cheap plastics?
    • ed_balls 8y ago
      > health impact of its cheap plastics Do you mean the health impact of when the device is thrown away?
      • evolve2k 8y ago
        I think they mean of small plastic particles coming off the cheap device and polluting the air.
        • Arn_Thor 8y ago
• ggregoire 8y ago
  Might be a stupid question but does this work for external air pollution? I live at the 20th floor in a city with terrible air quality and we open the windows once or twice a day.
  • mannykannot 8y ago
    I imagine it would help with particulate matter (such as smoke, whether visible or not), but I do not think it would have any effect on gases such as ozone, sulfur dioxide or nitrous oxide.
    • ed_balls 8y ago
      That's correct. HEPA filters anything bigger than 2,5 μm e.g. https://en.wikipedia.org/wiki/Benzopyrene https://en.wikipedia.org/wiki/Benzopyrene and NO2, SO2 etc. are 1000x smaller.
• Qerub 8y ago
  Nice synchronicity that this was posted the same evening I got a ~160 USD Xiaomi Air Purifier 2 (https://www.mi.com/global/air2/ https://www.mi.com/global/air2/) delivered home. Might be a good alternative for those who want an off-the-shelf product, a pretty design and "smartness" like scheduling.
  • woogiewonka 8y ago
    Scrolljacking on this site is unbelievable.
    • vinay427 8y ago
      I didn't notice any? I just tried with my ad/tracking blocking disabled as well.
• LeoPanthera 8y ago
  Huh! I independently "invented" this myself a couple of days ago when the Camp Fire blanketed the bay area in smoke. I got a 20x20 filter and some duct tape from Home Depot and a box fan from Target. (After discovering that Home Depot only sells fans in the summer.) I don't think I was the only one, though. HD was doing a brisk trade in 20x20 filters, and I think I bought the last box fan at any Target in the entire bay area. My "creation": https://i.imgur.com/jeJfqeW.jpg https://i.imgur.com/jeJfqeW.jpg
  • koolba 8y ago
    That’s looks as professional as anything I’ve put together! Is that the spot of use as well? I’d imagine the vicinity of the wall would limit the airflow.
    • LeoPanthera 8y ago
      Yes but it’s not as close as it looks. There’s about 2ft behind it.
  • jchrisa 8y ago
    The future is already here, it's just not evenly distributed.
  • HillaryBriss 8y ago
    nice job. can you say anything about the difference it makes?
    • LeoPanthera 8y ago
      I can tell you that it doesn't smell of smoke in the house anymore. I still have a sore throat, but I also have to go outside a lot, so maybe that's not surprising.
  • Scoundreller 8y ago
    When you can't get house parts, try auto and computer parts. Get some 120mm fans (or an array of 80mm, etc), and some engine air filters. Don't change the filters too often: "It is common, however, for servicing to occur when the filter appears dirty. Engine air filters are designed to actually increase their efficiency by using this initial layer of dust as an added filter layer. Initial filter efficiency is usually approximately 98% but increases to more than 99% by the end of the service life of the filter. Therefore, changing an air filter before the useful service life is achieved can result in premature engine wear." https://www.fueleconomy.gov/feg/pdfs/Air_Filter_Effects_02_26_2009.pdf https://www.fueleconomy.gov/feg/pdfs/Air_Filter_Effects_02_2...
• Dave_Rosenthal 8y ago
  I spent the weekend researching, implementing, etc. air filtration as one of those affected by the CA fires. It was worth it! The first step for me was getting a device to measure particles in the air. The air quality index (AQI) is an aggregate score that is made up of contributions from several harmful components. Of these, the quantity (weight/volume) of small particles (<2.5um) is often the large contributor. This is called the PM2.5. Directly measuring PM2.5 is very hard, requiring a device that eliminates the larger particles from the air (typically a cyclonic separator it seems) combined with some way of capturing and weighing of the very small quantity of remaining particles (we're talking ug/m^3). Many home air quality sensors instead measure the count/volume of particles larger than 2.5 um and call that the "2.5um measurement". You can see the problem. I bought a laser particle counted called Dylos DC1100 Pro. The Dylos measures particles counts larger than 2.5um as is common, but also counts particles larger than 0.5um. Of these two numbers, the 2.5 count is only vaguely correlated with the actual PM2.5 measure, but the 0.5um count is highly correlated. A bit of internet research (it seems many people have used the Dylos meter in various projects) and I was able to construct a scale to correlate 0.5um+ counts to PM2.5, and therefore AQI. (0.005*count~=ug/m^3) OK, all that done, to the filtration. First, I installed 3M 1550 MPR furnace filters (~MERV11). The "1550" is a measure invented by 3M 'MicroParticleRating' (or something) and is supposed to speak to how well the filters remove small particles. However these furnace filters don't really knock down very small particle counts in once pass. Sure enough, putting the particle meter at an air duct, the large (2.5+) particle count was way down, but the small particle count was only down a little bit (15-25%?) from the ambient air. Net effect is that after running for several days my house numbers are about 1/3 of the outside air counts. I also bought a BlueAir HEPA filter for my bedrooms. HEPA is supposed to be 99+% effective for particles 0.3um and up. This filter is in a whole different league. The particle counter placed on top of the filter returns near-zero small particle counts and does a much better job eliminating smells. The room they were in got down to 1/10 of outside levels. Overall I'm glad I got both types of filters, we are sleeping better, and the meter was very helpful to understand what was going on.
  • deleted 8y ago
    [deleted]
  • 8y ago
• valarauca1 8y ago
  I built a similar model over the weekend: https://twitter.com/valarauca1/status/1061362369702445056 https://twitter.com/valarauca1/status/1061362369702445056 Used an existing box fan. I had to buy duct tape ($3) and the filter I used one rated for 0.1micron pollen and viruses cost me $17 (rounding up after tax). I cut up a plastic safeway bag to make the seal around it. Seeing as most smoke particles is around 2.5-.5 micron I figured it'd be okay. I threw this together at about 7am on Saturday after I woke up coughing my lungs out at 6am (I live in the bay area). Just a quick trip down the the Homeless Despot to get the parts and throw it together. All things consider it works great. The air in my apartment is easy to breath, but if I leave without a respirator (even today) I cough uncontrollably. --- As of Tuesday evening it has been running for 4 days straight (no overheating). And has started to become noticeably brown. Needless to say I'm thankful for it.
• tra3 8y ago
  I wonder if you can put a filter on both sides of the box fan.
  • TylerE 8y ago
    There would be very very little gain from doing so, but you'd probably kill the motor. HEPA filters are very very very good. Running through 2 of them isn't going to pull much more out because there just isn't much more. Actually, you'd probably get less actual filtration due to the greatly reduced airflow.
    • tra3 8y ago
      Why would it kill the motor? Load is reduced when airflow is restricted. If the first filter reduces 90% of pollutants, can we assume that the second filter reduces an additional 90%?
• js2 8y ago
  Also works for dehydrating fruit: http://frugalvagabond.com/the-box-fan-dehydrator-experiment/ http://frugalvagabond.com/the-box-fan-dehydrator-experiment/
• gregwebs 8y ago
  I have been quite happy with the top pick from this review: https://thewirecutter.com/reviews/best-air-purifier/ https://thewirecutter.com/reviews/best-air-purifier/ Although the price of that purifier is now $40 more then when I bought it, so it may make more sense to look at their other picks.
  • ar_turnbull 8y ago
    I have the same one and think it’s great. Bought it when the wildfires in British Columbia blew over and turned Calgary into an apocalyptic wasteland. Air quality was bad and I’m still not sure what kind of filtering my condo building has.
• abalone 8y ago
  Can we talk about Molekule? Their team and some SF tech community folks have been plugging it all over Twitter during this tragic wildfire crisis. But it seems like snake oil to me. It’s $800. Certainly for smoke particles it can’t possibly offer any more protection than a standard HEPA filter. But even for its claimed ability to nuke VOCs, the claim seems ridiculous. While particles can deterioriate under prolonged exposure, the airflow must be too high and the exposure too short to make much of a difference. What gets me is how these guys misuse “science marketing” to play on people’s fears about germs. Add the shameless exploitation of a real tragedy here.
  • deleted 8y ago
    [deleted]
  • buzzy_hacker 8y ago
    I agree it seems sketchy. NYTimes writes, “Unlike virtually all other air purifiers—and all we’ve tested—Molekule is not HEPA-rated and does not claim to eliminate micron-scale particulates with a filter. Instead it claims to remove smaller, nanoscale pollutants, including VOCs and viruses, via a chemical rather than a physical process. Out of curiosity, we requested a model for testing for VOC reduction, but Molekule requested conditions around the testing that we could not agree to.” https://thewirecutter.com/reviews/best-air-purifier/ https://thewirecutter.com/reviews/best-air-purifier/
    • ejstronge 8y ago
      > NYTimes writes, “Unlike...” While the New York Times Co. did indeed purchase The Wirecutter/The Sweethome, there’s no reason to start attributing Wirecutter reviews to the parent company. This is especially true in the settings of reviews, since the NYT performs its own reviews.
  • leon_sbt 8y ago
    I have a hard time taking them seriously. Some of their "independent" lab results are from some USF lab. The same lab one of the co-founders was a director for... Go figure. Some please correct me if I'm wrong. Read the results in technology, and then read the bios of the people.
• ocdtrekkie 8y ago
  Insanely simple idea when you think about it. Side perk: My furnace uses the same size filters, so it won't even be a hassle to stock ones that fit a box fan.
• benbojangles 8y ago
  I built my own air purifier in 2016, living in London, I was living in a basement and was having breathing problems due to mould. My landlady was gaslighting me at the time, so I built the air purifier. It worked for a while but mould spores cling to the paper filter and eventually grow into the filter material. I think Dyson uses glass fiber filter to stop this problem. My filter helped a lot, but eventually I had sclerosis infection on my brain and ended up in hospital with lung infection and brain lesion, still recovering after two years, and I will never be my old self again. I was subletting so had no grounds for complaint, I had to choose between homelessness or phoning a distant relative I hadn't spoken to for 24years, I chose the latter and I think it's the reason I'm still here.
  • simonebrunozzi 8y ago
    Wow, what a story. Thanks for sharing it. I feel bad for you, and sincerely hope that you are back on your feet.
  • electic 8y ago
    Woah, this is pretty scary. Thank you for sharing. How did you know it was mold that was in the air? Is there some sort of test kit that you can buy to test for this. Mold is pretty hard to detect because you can't really see it because it typically hides between the walls. Any advice appreciated.
    • the_clarence 8y ago
      You can notice black spots in your bathroom or other places where steam doesn't escape properly. I noticed it on my mattress also. I don't think I have any health issues because of that, it was 5 years ago, but it was rough.
      • marco1 8y ago
        Mold is not always black, is it? It can have other colors as well, e.g. yellow.
    • sgc 8y ago
• mynameishere 8y ago
  They used to sell these--box fans with connections for furnace filters. I found it strange that they never caught on, and now you can't find them anywhere.
• user764743 8y ago
  You could also buy a plant.
  • oh_sigh 8y ago
    Plants don't remove particulate matter like an air purifier does
• akeck 8y ago
  Note that restricting airflow on a radial fan can cause the motor to heat up. Make sure you get a 20-inch fan with a fuse. To reduce heat, increase air flow by making a box with three filters and by using 2 inch deep filters. Also, when I built my three filter "box" last fall, I was able to order a set of three MERV-13 20x20x2 filters directly from Nordic Pure for less than what they cost on Amazon. Finally, to make a cube, cut the remaining sides from the filter box. Then roughly tape it together with small pieces of duct tape. When the filters and panels are in the right spots, seal it completely with duct tape. Remember to put the box of filters on the "pull" side of the fan with right sides of the filters facing outwards.
  • trisiak 8y ago
    Linked projects put the filters on the opposite side to what you're suggesting. Can you elaborate more on why do you think the filters should act on the air coming into the fan? Is it to increase heat dissipation of the motor?
    • sigstoat 8y ago
      putting it on the intake keeps the motor cleaner (which will help with motor life), you can vacuum the filter without disassembly, and the air flow will tend to help the filter stay on, instead of pushing it away.
  • sgc 8y ago
    I agree with placing the filters on the pull side, since that is what all hvac units do and what the filters are designed for. To be effective, you are also corrected that a deeper pleated filter with more surface area is the only way to go. But I am unconvinced the motor will heat up. Certainly there will be less air so if it is air cooled it will heat up from that, but at the same time, a fan in a partial vacuum uses less energy and should heat up less. Just slap a meter on it and you will see the draw can be significantly lower, since it is doing less work.
    • meesterdude 8y ago
• apo 8y ago
  Nifty idea, but I'm not sure I agree with the technique used to prove effectiveness: https://www.youtube.com/watch?v=kH5APw_SLUU https://www.youtube.com/watch?v=kH5APw_SLUU The narrator puts a particle counter in front of the fan and notes the 90% reduction. So far so good. The problem is extrapolating this result to the entire room. Yes, maybe you'd get close to 90% if the device were allowed to run a few days. On the other hand, it could leave the situation worse (by blowing existing particulates around) or unimproved (by failing to filter room air efficiently enough. Either way, I'd like to see see a controlled study. Two identical rooms with identical usage. One gets a homemade filter. The other gets just a fan of the same make and model, maybe with a dummy filter to baffle airflow. What's the average particle count in both rooms after, say one week?
  • tfha 8y ago
    With pre-registration, while we're at it
  • gnopgnip 8y ago
    This DIY version does not have the same pre filter as commercially available ones, and would need to have the filter changed more often at a minimum. There are studies showing the success such as this one. https://www.ncbi.nlm.nih.gov/pubmed/9192919 https://www.ncbi.nlm.nih.gov/pubmed/9192919
  • CompelTechnic 8y ago
    If you check out Matthias wandel's YouTube channel, he does some experiments with hours-long recording of room particle counts. This is in a woodshop (sawdust) setting with a similar diy filter setup.
• wenc 8y ago
  I wonder: if one is generally healthy and the air quality is unproblematic, should one get an air filter? Does air filtration potentially lower long term immunity and make us less tolerant to particulates? I worry about the long term effects of being “too clean”, that is, I think there’s something to hygiene theory of disease. The body needs small stressors and perturbations in order to thrive.
  • hourislate 8y ago
    I wouldn't worry about this if you live in a city. The amount of vehicle exhaust, brake dust, and just general stuff in the air will make up for and most likely counter the time you spend in a clean breathing environment.
  • joelcollinsdc 8y ago
    Generally I want to agree with you, but there is also research going the other way... https://www.epa.gov/pm-pollution/health-and-environmental-effects-particulate-matter-pm https://www.epa.gov/pm-pollution/health-and-environmental-ef...
  • stevenwoo 8y ago
    This article references a more recent London study but mentioned is a more extensive California study of children. TL;DR; One really, really should not live/work any closer to a road with (18 wheelers) traffic than one has to, for children it is paramount - I think all schools in Southern California close to a freeway have filtration systems for this reason. https://www.theguardian.com/environment/2018/nov/14/diesel-pollution-stunts-childrens-lung-growth-london-study-shows https://www.theguardian.com/environment/2018/nov/14/diesel-p...
• noobermin 8y ago
  You've got to be kidding me. But yes, if you literally have a fan and a filter then why do you need to spend more money.
• rubatuga 8y ago
  Tried this exact same thing. Unless you are a "fan" of noise, and the inability to sleep next to it, go ahead. It's not worth it IMHO. I ended up just turning it on whenever I left the house, but even then my roommate started getting annoyed from the other side of the apartment.
• Fej 8y ago
  How fast does this burn out the motor? Legitimate question. I just built one of these.
• jordache 8y ago
  literally HACKER news
• lilbobbytables 8y ago
  I've been using a setup like this for the past year. I use a 4" think filter to reduce strain on the motor though (it's pleated, so a lot more surface area to pull air through than the thinner ones), the idea being reduced strain on the motor. I also stick a carbon pre-filter in front of it. I get smoke wafting in from outside via window air conditioner - and I think my neighbor occasionally smokes in his room. I'm planning to setup another to better cover my open floorplan.
• dmourati 8y ago
  I have the ~$800 pro version early in the video. It's an IQAir. I bought it when I bought my house. We were refinishing the hardwood floors and have a small child. My goal was to knock down the VOCs to make the room safe for him prior to move in. It runs 24/7 in my bedroom now. Huge improvement in sleep quality. I've only had to change one of the filters once for about $100 after 1.5 years of run time.
• jakeogh 8y ago
  These work excellent. I put a finer filter on the output. Clear difference in the pollen seasons, but I just let it run all year and swap the (visually clogged) input filter every few months. The FPR10 output filter lasts longer, but you gotta take a look at the side facing the fan to inspect it. Also, consider adding output filters on any AC units (ducting etc). Even a "new" AC system can quickly become a source of particulates, or (way) worse.
• peferron 8y ago
  Important tip: if you set up an air purifier in your home, make sure to plug all drafts around your house: windows, doors, etc. Even a DIY purifier with small airflow can make your indoor air excellent if given enough time to do so and no leaks to fight against. If you want to get some fresh air in your home, do not leave a window half-open all day long—instead, open all your windows at once to cycle the air as fast as possible, then close them again and let the purifier do its job. If you do that in the morning (ideally just before leaving, if you aren't staying home), you'll have great air quality through the entire evening and night. Since we're on HN, I'll also mention a toy project I built a while back [0]. It uses a Raspberry Pi to read particulate matter sensor mesurements over serial link from a Dylos 1100 Pro, then pipes it into Redis and InfluxDB and ultimately Grafana for presentation. I've used it to track the air quality in my home in for the past year or so and it's pretty fun. In my case, cooking is usually the biggest contributor to poor indoor air quality! [0] https://github.com/peferron/air-quality https://github.com/peferron/air-quality
  • hinkley 8y ago
    Also open your windows when you vaccuum. Send most of the dust outside instead of just what gets caught in the filter.
  • lappet 8y ago
    This is great! Thanks for sharing :)
  • heybrendan 8y ago
    Very interesting! How does the Dylos 1100 Pro compare to, for example, the Nova SDS011 sensor? By my cursory review, the SDS011 is much cheaper and appears to offer a more native Raspberry Pi-compatibility experience. Is the Dylos more precise? Can it produce readings the SDS011 can't? Are the two sensors measuring fundamentally different things? Finally, if you had to do it all over again, would you choose a different sensor or stick with the Dylos? Thanks for sharing your project and for your insights!
    • peferron 8y ago
• NoblePublius 8y ago
  I’ve been doing this for years. Cheaper drugstore fans can’t handle the drag of the filter and will burn out. Kind of amazing that no one makes a box fan with slots for such a filter.
• giardini 8y ago
  Similar items are commercially available: "The Fan Buddy is an electrostatic washable fan filter that attracts and captures airborne dust, pollen, dust-mite debris, lint, mold spores and pet dander. It will also help reduce smoke and smog. This Fan Buddy fits on most 20 in. box fans... " https://www.homedepot.com/p/Fan-Buddy-20-in-x-20-in-x-1-in-Washable-Fan-Air-Filter-FB-BF-20/206210062#product_description https://www.homedepot.com/p/Fan-Buddy-20-in-x-20-in-x-1-in-W...
• squarefoot 8y ago
  Can those filter be washed? People living near car congested areas would benefit from them the most but should also swap them more often.
  • woogiewonka 8y ago
    I don't think so. The filter he uses has to be replaced every 3 months and it costs ~$15 (that particular brand). So you are looking at $60/year in filter costs - all in all not bad! Also, you could stick a carbon pre-filter right in front of the fan (behind this filter) of it to filter out some of the odor-causing particles.
• yborg 8y ago
  So I did this with a cheap $15 box fan and a MERV 13 filter. It performs very poorly, the filter impedes the airflow too much and the fan actually will intake most of the airflow from the front corners of the output side because it's less resistance. Axial flow fans only operate efficiently at low static pressures. This is why your home forced air system uses a centrifugal blower, which is more efficient at high static pressures. tl;dr I'd use a MERV 11 or less on a cheap box fan. You aren't going to make a Class 100 clean room out of your house with this kind of setup.
  • woogiewonka 8y ago
    Your comment should be at the top of this thread. This guy never mentions fan performance after applying a strong filter like Merv 13. I did the same and the airflow is reduced significantly. Since other systems use a strong motor, this box fan contraption does not compare in the slightest. You'd have to have it run at high setting ALL the time. Imagine that...
• MarkMc 8y ago
  I worry about air pollution especially when I'm in Jakarta or Singapore so I bought the Dylos DC1700 air quality monitor. It is great to know exactly how bad the pollution is and how effective my air purifier is - I feel like I'm walking around with x-ray vision.
  • adakbar 8y ago
    Know any merchant who sells Dylos DC1700? I'm in Jakarta too, kinda hard to find these kind of hardware
    • MarkMc 8y ago
      Sorry I don't know anyone who sells in Jakarta. I purchased it on Amazon.com and used the myus.com service to forward it to me. It's expensive but worth it for my health.
• ksec 8y ago
  Do we have any other alternative to HEPA filtering, or something that last 5 years without me paying to replace it every 1 - 2 years? All the current Air Filtering system are like Printers, they earn more money with the yearly filter replacement. I also wonder if it makes sense to have an Air Filter if I have my windows opened 80% of times? I like the better Air Circulation, but the Air Quality aren't exactly great either. We now live in a world with pipes that have potential toxic materials and water contaminated so we need Water filtering system, and Air pollution that needs Air filtering system.
  • Havoc 8y ago
    The filters I've got for a cheap commercial one are said to be fine for 6 months. Windows open - pointless if there is significant airflow. I've got a window open too, but no significant airflow resulting from it.
  • Elien237 8y ago
    Particle filters such as HEPA are unfortunately by nature only effective for roughly 6 months, then they are clogged. You can vacuum them to get rid of the biggest particles and then use them for another 6 months (total 1 year), but then they are clogged at molecule level and are perhaps only 25% effective of its original efficiency and won't do you any good. The washable ones are not good and the ionization air purifiers without filtration are a scam. Particle filters are the best way to give you good air quality. And unfortunately you get what you pay for. When it comes to carbon filters they don't work for more than 6 months - no matter how good air quality you have. Carbon will absorb till it finds equilibrium then start to release smells and some gases. Shelf life of an opened package is about 6 months even if you don't push air through. Depending on the air quality in your local area (Bombay smog/wild fires/countryside clear skies), your filters will be clogged eventually and a rough estimation is 4-6 months in high polluted areas, and 1 year in less polluted areas). Turn the air purifier off when you have the windows open. It makes no sense to use it if you let pollutants in from outside, even if your indoor quality is bad.
• ipsum2 8y ago
  Has anyone tried constructing a UV-C based filter before? You would need to be careful to make sure no light leaks out.
• xhruso00 8y ago
  That guy's wearing a doctor coat and has lots of books on the shelf so he is legit for sure. THUMBS UP.
• thewhitetulip 8y ago
  Edit: plants do nothing to particle matter in air they can soak up co2, benzene, formaldehyde etc but do ample resesrch before placing plants in your bedroom. Typically snake plants are fine in bedroom as they don't give out CO2 at night. There is no need for an air purifier if you have ample light in your room. Just plant a few indoor plants Peace lily Rubber plant Snake plant Spider plant Aloe vera Money plant Orchid NASA has done a study in the 80s and these plants have purified a lot of harmful gases including Benzene, formaldehyde, CO etc Please use more plants!! And on top of that few plants like Snake, Aloe give oxygen during day and night so they are refreshing (as in they don't just clean air they give oxygen as well) and plants are cheaper and require just water and fertilizer every once in a while. I own 40+ plants in my balcony garden itself. I've experienced these effects first hand!
  • TeMPOraL 8y ago
    Apparently this NASA study needs a huge asterisk next to it. https://news.ycombinator.com/item?id=18193622 https://news.ycombinator.com/item?id=18193622
    • thewhitetulip 8y ago
      What? I have read the report myself. They put in Benzene inside a sealed room and one of these plants. A few hours later the Benzene was gone! Absorbed by the plant. They did the same with formaldehyde too and other harmful substances. Isn't that the bar for purification? This is still better than mere air dolter that are costly and requore frequent maintenance
      • TeMPOraL 8y ago
        I think the key term here is sealed room. And this does not invalidate the study, only helps evaluate the results in context of applying at home or office. I.e. it's still gonna help, but unless you restrict your airflow, not as much as you'd like. Though the same caveat probably applies to all air purifiers too.
• adakbar 8y ago
  Is there a place where I can get information about the MERV rating of certain HEPA filter products?
  • xVedun 8y ago
    MERV info: http://www.mechreps.com/PDF/Merv_Rating_Chart.pdf http://www.mechreps.com/PDF/Merv_Rating_Chart.pdf
  • deleted 8y ago
    [deleted]
• oblib 8y ago
  I use this same setup and it works great. Been doing it for years.
• lmilcin 8y ago
  I see some comments on fighting mold and smells, I have an experience devising my own protocol that was extremely successfull in my case. Few years back I was desperate to find a large apartment in an area where they are just not available. I found one, extremely cheap, that the owner could not find anybody to rent to. The apartment was all but destroyed by previous occupants -- there was substantial mold in most rooms, heavy cigarette smell that was completely masked by even worse problem -- monkey pee and feces on every flat surface in the apartment. Being geek I decided I will try what I can do and in the end I devised a protocol to treat the apartment. My girlfriend was very sceptical. A month later I brought her to apartment to the smell of fresh furniture and she was instantly converted. There was no fresh furniture, it was just the other smells were completely eradicated. The only smell I could not get easily off and lingered for many months was banisters that were painted over with lacquer by the owner before I had the chance to treat them. The treatment was: 1. industrial ozone generator (200 USD) + 200W fan + air dehumidifier (ozone decays quickly in humid air) + programmable timer and remotely controlled (over Internet) AC socket to control fan and generator (this let me turn the fan for 20 minutes every hour and let me turn everything off 3 hours in advance so I can visit safely without being subjected to high levels of ozone). This setup was on for an entire month except for when I was visiting to do other stuff in the flat. 2. 35% hydrogen peroxide mixed with baking soda. Ozone kills mold, binds and oxidises any smells except for urea crystals. To neutralize urea crystals you first have to dissolve them and treat while in dissolved state, before they crystalize again. I don't know what baking soda does, exactly (except for making cleanup tougher...) but I found dissolving some improves the treatment with hydrogen peroxide. I sprayed every surface (walls, floors, furniture, etc.) in the flat with this mixture enough to get it wet so that it dissolves and reacts with urea crystals. Now, mandatory WARNING: both concentrated ozone and 35% hydrogen peroxide IS EXTREMELY DANGEROUS, you absolutely MUST spend time researching how to handle this stuff safely. The hydrogen peroxide at that concentration INSTANTLY BURNS ANY ORGANIC MATTER IT IN CONTACT WITH. This includes your lungs and eyes if they come in contact with vapors or mist. Concentrated ozone may also leave lasting effects on your eyes and lungs. MAKE ABSOLUTELY SURE NOBODY ENTERS YOUR FLAT WHILE IT IS BEING TREATED, MAKE SURE OZONE IS NOT VENTING TO OTHER APARTMENTS, ETC. One minuscule drop of 35% hydrogen peroxyde touched my finger and it felt as if I was shocked with electricity and the skin was instantly burned white. Don't even think about getting close to it without heavy nitrile gloves and face mask. The fumes and mist will be extremely dangerous, I have used full face mask with external breathing aparatus to be on the safe side while I was spraying entire flat with it. Test the effect on any surface before treatment and dilute with water until it becomes safe for that surface. I have destroyed some stuff at the kitchen where it reacted with plastic foil on otherwise metal oven exterior, etc. I ended up diluting it for everything except stained walls. For furniture I diluted it to around 5-6% hydrogen peroxide, for floor panels to around 9%. ALSO, very important, 35% hydrogen peroxide naturally decomposes producing lots of hydrogen so if you store the containers for longer than few days you have to constantly monitor them and vent hydrogen before containers burst. Once you finish your treatment, get rid of it as quickly as possible -- it is a liability while you are storing it. On the upside, and this was very important to me, this does not leave any lasting dangerous chemicals in your flat. Both the ozone and hydrogen peroxide decompose naturally into harmless products and baking soda is the only think you can really work to get rid of but only for cosmetic reasons -- so that your entire flat does not look as if it is covered in dust.
• Cthulhu_ 8y ago
  Wouldn't turning on the extractor in your kitchen have the same effect? If you've got the correct filter in there anyway.
  • strstr 8y ago
    If the filter type is right (as you mention) yeah that would make sense. If it vents outside though, not necessarily. Running the extractor would drop air pressure and pull from elsewhere (particularly bad during times with low air quality).
• Havoc 8y ago
  Given how cheap the commercial ones are I'm not sure I see a point. Esp given the fact that the motors in box fans are unsuitable for the task. I just ordered a wifi plug for mine though so that I can set it on a timer / hacked amazon dash button. It's not but the slight whoosh is annoying
• okasaki 8y ago
  Where do you get these parts in the UK? The MERV 13 20" filter is 140GBP on amazon.co.uk and 20" box fans are 40-50GBP.
• nathan_f77 8y ago
  That's a really good idea. I was planning to buy one for a few hundred dollars, but I should just do this instead. The burning season is really bad in Chiang Mai (lots of smoke in the air for about 2-3 months), so it's good to stay indoors and have an air filter.
  • kilroy123 8y ago
    Off topic, but hey so I just moved to Chiang Mai. Do you think it's worth even sticking around here during that time? I was thinking about just heading to Bali instead. Not sure how bad it really gets.
    • nathan_f77 8y ago
      It's really awful, especially if you're sensitive. Some people aren't bothered by it too much, but it really affects me, so I try to get away. We have some pets, but it hasn't been too hard to find a house-sitter. (Although I always feel a bit guilty, and try to be honest about the smoke.) These articles are concerning: * https://www.theguardian.com/environment/2018/aug/27/air-pollution-causes-huge-reduction-in-intelligence-study-reveals https://www.theguardian.com/environment/2018/aug/27/air-poll... * https://www.scientificamerican.com/article/air-pollution-a-leading-cause-of-ca/ https://www.scientificamerican.com/article/air-pollution-a-l... I think we'll move to a new city or country in the next 12 months. I don't think it's wise to go through burning seasons once a year for a few decades. (It's actually the only reason we want to move, otherwise Chiang Mai is an amazing place to live.) Bali would be a good option, or even the south of Thailand if you have some more time on your visa. Koh Lanta is great.
      • kilroy123 8y ago
        Awesome thank you much for the links! It seems like a very awesome place so far. I'm loving it.
• CathyWest 8y ago
  What kind of furnace needs this high level of air purity to operate? I would have thought a grating that prevents rats and squirrels from wandering in would suffice. I would assume small particulates would just burn with the rest of the fuel with no ill effects.
• Andymoore 8y ago
  mine brother too working in construction business and having same breathing problem.
• agumonkey 8y ago
  Anyone knows how to DIY microfilters ? or even nanofilters ?
• Odenwaelder 8y ago
  Cool! You could use a smart plug and a fine dust (PM10 and PM2.5) sensor to start the fan only if the air is bad.
• chanandler_bong 8y ago
  reddit.com/r/thereifixedit
• samsolomon 8y ago
  If anyone is looking for general air purifier recommendations. I'm a huge fan of Coway systems. I have pretty bad allergies purchased a Coway Airmega 300 for my 850sq ft studio. I've had it for about 6 months and been incredibly happy with it. I wrote some initial thoughts about it here. https://productdork.com/t/coway-airmega-300-vs-400/56 https://productdork.com/t/coway-airmega-300-vs-400/56 It has to be the best looking air filter on the market—I wanted something that would look good in my place when I have people over. Beyond that it is extremely well designed and the pre-filters are super easy to clean. I got mine on sale for about $400. For smaller rooms the Coway mighty is a better and more affordable pick. It doesn't look as nice, but it is currently at the top of The Wirecutter's air purifier recommendations. You can find it on sale for around $180. https://thewirecutter.com/reviews/best-air-purifier/ https://thewirecutter.com/reviews/best-air-purifier/
  • elektor 8y ago
    I have 2 of the $180 Coways and so far am pleased with them. Once in a while, I will light a candle and when I blow it out, will hear the air purifier go on full-blast (Speed 3) to clear the air. Interestingly, it sometimes turns to medium power (Speed 2) when I'm just shuffling around the room. I imagine its because I have a few rugs and its pushing up a lot of dust.
• egghat 8y ago
  Check out the blog http://particlecounting.tumblr.com/ http://particlecounting.tumblr.com/ The writer has tested a lot of combinations of fans and filters (Simple, HEPA, Activated Charcoal). It's astonishingly easy to build a combination that costs way less than a "professional" Air filter. The writer has put his findings into a "social startup" that builts these simple, but very effective airfilters in some developing countries: https://smartairfilters.com/cn/en/product-category/diy-air-purifiers/ https://smartairfilters.com/cn/en/product-category/diy-air-p...
  • hermosa 8y ago
    I use the SmartAir filter setup in Shanghai. It works great and the founder's blog is very useful. I'm glad to support the project.
• Elien237 8y ago
  I’ve been reading and following these comments now and I’m both impressed and horrified at the same time. As a mechanical engineer, product developer and developing air purifiers specifically for 5,5 years in combination of filter expert till just 6 months ago. I now work in another industry. You can ask me anything and I’ll do my best and be as unbiassed to brands as possible if you want me to. There are a few things you need to know for your own safety if you do DIY and want to reduce costs: Fan and filter are the heart of the unit. This is where you put the money even if you want to do a temporary solution. The housing can be cheap, but please be smart and never leave a DIY unit alone since electricity is involved, they are not safe. Once you’ve bought all this equipment, you’ll soon realize you have put out a cost of a reasonably good air purifier. - You need to have a good amount of space between the filter and the fan to cut pressure drop – otherwise you will overload the fan, you get a high electrical bill and it becomes a fire hazard or it will break down = your money is not well spent. This is why you see some units on the market looking hollow – the space is there for a reason. - Fans. Look for a strong motor that can handle air resistance. Regular fans are not made for resistance and will break, stop (programmed) or even start a fire. Also look at the airflow rate and the safety regulations of it. The higher airflow rates the better. When it comes to fans, you get what you pay for. - If you use a weak fan and a thick filter you will only clean the air closest to the fan, not the actual room air = money not well spent unless you use the purifier right in front of your mouth/nose. - HEPA filters are actually not that great... There are newer filter types on the market that are less dense but still not as effective. HEPA can be too thick/dense for the fan to be able to pull air through, or the air doesn’t have high flow enough to clean more than just the air next to the purifier. You need to have circulation. Especially fans that are made to only move air without resistance, the motors are not adapted for this. If you have a strong fan you can use HEPA (Merv) since it can power through. Also, if the filters are too thick, air leakage will occur, motor will sound horrible, and the air will pass on the side instead of through the filter = noises, whistle sounds and less clean air. Yes, duct tape is good here if you build it yourself. - Put the filters in front of the fan (before fan) to spare the life of the fan – the dirt will not accumulate and destroy the fan over time. To get (collect) dirt in the filters is the goal. Some fans can handle dirt passing through and then you can have the filter after. However, if you just buy a regular air fan in a regular store, I don’t suggest having the filter after the fan (air flow direction). - If the filter gets super dirty quickly, you can vacuum or gently whip it outdoors to recover some lifetime. However, after some time (roughly 1 year in normal use) it will be clogged no matter what you do. There are no filters or technologies better than particle and carbon filters available today. The 6-months to a year lifespan is actually accurate in normal conditions. I’ve been doing these tests in China, India and Europe and US several times in different conditions (both lab standard and normal homes) and with different units/tech/brands etc and can confirm particle filters + ionization is the best tech available and the filters last 4 months-a year depending on local conditions. The filters are usually functional after a year as well, but with very low efficiency. - Pre-filters are great since they take on large particles like pollen or ashes before it hits the main filter. Just make sure it’s not too dense. - Fully made air purifiers are tested by 3d party institutions unbiased to payments or commercial, certified and heavy controlled before released on the market. You can check consumer reports, AHAM and California Air resource board (ARB) or Chinese GB-standard websites for different type of tests and results if you want to know which ones are really, really good. Some complain that they are in “lab environments” but it’s still really good products that does the job even in real life conditions. - If the unit you want is not in their lists of tested products, it’s a warning sign that the product is not good, or might not even qualify as an air purifier… It’s a surprising large number of big brands that make terrible products but are good in marketing or simply rely on their names. - Fully made air purifiers have fans developed specifically to match the filters resistance and won’t break down after a few months or start a fire if put under heavy resistance (clogged filters). The filters last longer since its optimized for air treatment in home environments. Usually other technologies are a part as well such as ionization or UV or similar. That’s why they are more expensive. They are super important in a development of air purifies. Some of them also have IP44 certified fans meaning they can work during humid conditions without breaking or causing short-circuit/burn outs or worse. - These DIY things work, but are usually not cheaper in the long run and are not as effective as the real purifiers. If you suffer from fires, smog, allergies etc I highly suggest getting a real purifier incl filtration+ionization since those things are very harmful, especially for children. If you just like to temporary fix something these DIY will work if you do it right. I hope I could answer some of your questions.
• CarVac 8y ago
  I made a custom wooden computer case with 8 120mm fans and a furnace filter over the intake. The computer side is positive pressure and is as clean as the day I built it 4 years ago. I buy filters in bulk from McMaster Carr for $5 apiece.
  • rsync 8y ago
    Mcmaster carr[1] is a wonderful commerce website and I am so happy I found them. I buy all of my fittings and hoses and so on from them. [1] https://www.mcmaster.com/ https://www.mcmaster.com/
• black-tea 8y ago
  Would this do anything to help with air pollution from a nearby road? I'm thinking particulates from diesel fumes.
• davio 8y ago
  Repurpose this device as a jerky dehydrator too: https://altonbrown.com/beef-jerky-recipe/jerky-blowhard-3000/ https://altonbrown.com/beef-jerky-recipe/jerky-blowhard-3000...
• grendelt 8y ago
  > "Videotaped" haha. Seriously? It was on tape?!
• rustychris 8y ago
  In case you're curious how this does with wildfire smoke -- Oakland 1 bedroom, put a 14"x20" MERV 13 (filtrete blue) filter on a box fan (covering the extra 6" with paper). Had a PMS5003 from adafruit monitoring before and after. In the span of 3 hours indoor PM2.5 dropped from 25 to 5 ug/m3 and has stayed low since. https://imgur.com/IxdxhV2 https://imgur.com/IxdxhV2
• LinuxBender 8y ago
  I think this is a cool project idea, but I would not use this as a primary means to filter air unless you can't afford a proper hepa filter unit and you happen to have parts laying around to cobble this together. Smoke and mold are dangerous to breath and you only get one life. This is probably a good way to augment your existing filters, in my opinion.
• patrickbuckley 8y ago
  Does anyone know if this type of setup would be good for smokey air from California wildfires?
  • rustychris 8y ago
    It works - we measured 25 down to 5 ug/m3 drop over 2 hours in an oakland townhouse. Measured with hobby grade (pms5003 from adafruit) hardware, so absolute numbers probably not that accurate, but the effect was clear.
• chefsaroar 8y ago
  Hi
• vic_b 8y ago
  I have found this on amazon seems like someone is already build a complete prototype. https://www.amazon.in/Smart-Air-DIY-Purifier-White/dp/B01CP55QXS/ref=pd_sbs_79_2?_encoding=UTF8&pd_rd_i=B01CP55QXS&pd_rd_r=979f7ddc-e969-11e8-8bb0-a509d9a0f381&pd_rd_w=fULSI&pd_rd_wg=QMAYi&pf_rd_i=desktop-dp-sims&pf_rd_m=A1VBAL9TL5WCBF&pf_rd_p=9fc668a0-2aac-4fb6-970f-606919bc0185&pf_rd_r=QA1DHXPWYMCWEE2HCYPG&pf_rd_s=desktop-dp-sims&pf_rd_t=40701&psc=1&refRID=QA1DHXPWYMCWEE2HCYPG https://www.amazon.in/Smart-Air-DIY-Purifier-White/dp/B01CP5...
• JesmineTyler 8y ago
  "Apparently, the contractor let the drywall get soaked while sitting on palettes during monsoon season, and since the roofing wasn't done there were inches of standing water that resulted in black mold. They just drywalled right over it. In the US. In 2018. In a luxury condo." I am sure such things happen everywhere in the world. I have lived in China for a long time, and you won't ever know how worse some of the construction companies are, they just want money by keeping things just looking good in the appearance.